MSc留学生作业代做、代写C/C++课程设计作业、代做C/C++实验作业、代写Digital Communication作业

Section 1.

Digital Communication and signal processing (30059)

- MSc assignment 2018-19

The assignment forms 50% of the final mark.

1. Each student should prepare a brief essay presented in a scientific paper format and style on a specific

topic of statistical signal generation and processing in communication systems. The format of the essay

is formulated in the Section 4 of this document

2. Each student will have an individual task, taken from the Section 2 of this document.

3. All the assignment shall have the same structure:

4. Introduction: To formulate the gaol of the study and to draw the system/sub-system block diagram.

Section 1: To explain the system operational principles including a small literature review and

mathematical description of the signal and noise presented in your system as well as an analytical

equations for the system performance evaluation.

Section 2: To draw the system model chart and explain the meaning of all blocks in the chart as well

as show the main signals at the blocks input and output in time domain and frequency domains. For

all random signals shall be presented figures with their power spectral density and probability density

function. For all deterministic signals shall be presented graphs with their spectrum and time domain

waveform.

Section 3: Comparison of analytical and modelling results.

Conclusion 4: Based on Section 3 results.

Appendix: Appendix with the programme codes is compulsory for all students.

The main text of the essay length should be between 2000 (minimum) and 3000 (maximum) words

plus Tables (not more than 4), Figures (not more than 12) and, if necessary, appendixes which

should not exceed 3 pages in total. All shall be prepared in accordance to IEEE paper presentation

standard presented in the Section 4 of this document.

5. Students are expected to show their ability to understand the subject area and the specified problem as

well as to demonstrate their technical communication and computer modelling skills. The essay should

be self-sufficient for readers.

6. The assessment criteria are at the last page of this document

Plagiarism, which includes, but is not limited to, a failure to acknowledge sources will be penalised.

Submission: Please use an electronic submission. The assignment should be converted in PDF. Late

submission will be penalised at 5% per day late. A schedule for the demonstrations will be arranged to suit

each person once the summer term timetable for revision lectures has been published.

The main recommended book: “Wireless Communications – Principles and Practice”, T. Rappaport,

Prentice Hall, 1996 and later edition as well as the lecture notes.

P a g e | 2

Section 2.

The topics are:

1. 1977317

Analysis and simulation of a communication system with 8-ary Quadrature Amplitude Modulation (QAM). BER vs

Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise.

Symbol rate 4.8 KS/s.

2. 1906728

Analysis and simulation of a communication system with 16-ary Quadrature Amplitude Modulation (QAM). BER vs

Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise.

Symbol rate 2.4 KS/s, carrier.

3. 1908270

Analysis and simulation of a communication system with 4-ary Phase Shift Keying (PSK) modulation. BER vs

Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise.

Bit rate 16 Kbit/s.

4. 1891765

Analysis and simulation of a communication system with 8-ary Phase Shift Keying Modulation (PSK).

BER vs Bit/Noise ratio should be analytically obtained and be simulated for BER 10-3

for computer generated

Additive White Gaussian Noise; 16 K samples per second. It shall be generated the noise and shown its

characteristics in time and frequency domain at the input and output of matched filter. In addition the simulated 8-

ary PSK signal in time and frequency domain shall be shown for the sequence 0010 1110 0101 0100 01110.

5. 1918928

Analysis and simulation of a communication system with Minimum Phase Shift Keying (MSK) modulation. BER vs

Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise

without pulse shaping. Bit rate 4.8 Kbit/s

6. 1971022

Analysis and simulation of a communication system with Quadrature Phase Shift Keying (QPSK) modulation.

BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive White

Gaussian Noise without pulse shaping. Bit rate 4.8 Kbit/s

7. 1887218

Analysis and simulation of a communication system with Gaussian pulse shaping technique for Minimum Phased

Shift Keying (MSK) modulation for the shape factors α=0.2. BER vs Bit/Noise ratio should be simulated for BER

10-2 and 10-3

for computer generated Additive White Gaussian Noise. Bit rate 24 Kbit/s

8. 1964710

Analysis and simulation of a communication system with Quadrature Phase Shift Keying (QPSK) modulation with

Raised Cosine Rolloff Filter with α=0.5. BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for

computer generated Additive White Gaussian Noise. Bit rate 4.8 Kbit/s

9. 1967289

Analysis and simulation of a communication system with Code Division Multiple Access (CDMA). Simulate signal

reception at a background of N interferences using M-sequences for signal spreading with the length M=1023.

P a g e | 3

BER vs N (Number of Interferences) should be simulated for BER 10-2 and 10-3

for computer generated Msequences,

presumably 4<N<32

10. 1892870

Analysis and simulation of a communication system with Code Division Multiple Access (CDMA). Simulate signal

reception at a background of N interferences using M-sequences for signal spreading with the length M=511. BER

vs N (Number of Interferences) should be simulated for BER 10-2 and 10-3

for computer generated M-sequences,

presumably 2<N<16.

11. 1914977

Analysis and simulation of a communication system with Code Division Multiple Access (CDMA). Simulate signal

reception at a background of N interferences using M-sequences for signal spreading with the length M=255. BER

vs N (Number of Interferences) should be simulated for BER 10-2 and 10-3

for computer generated M-sequences,

presumably 1<N<8.

12. 1466307

Analysis and simulation of synchronization channel operating with 13 Barker code Phase Shifted Signal 0.02

microseconds per chip with 5 GHz carrier frequency at the background of Additive White Gaussian Noise for the

false alarm rate 10-3 and 10-4

.

13. 1950646

Analysis and simulation and of one channel of Direct Satellite TV systems. BER vs Bit/Noise ratio should be

simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise.

14. 1971449

Analysis and simulation of one channel (satellite to ground) in Low Earth Orbiting Satellite mobile communication

system IRIDIUM. BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated

Additive White Gaussian Noise.

15. 1692710

Analysis and simulation of spread spectrum technique in GPS navigation system. One channel with 1023 Msequence

spreading should be simulated at a background of Additive White Gaussian Noise and N=4

interferences for BER 10-2 and 10-3

.

16. 1906577

Analysis and simulation of one channel of Zig Bee transceivers. BER vs Bit/Noise ratio should be simulated for

BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise.

17. 1964341

Analysis and simulation of a communication system with Differential Quadrature Phase Shift Keying (D-QPSK)

modulation. BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive

White Gaussian Noise without pulse shaping. Bit rate 2.4 Kbit/s

18. 1899925

Analysis and simulation and of one channel of Direct Satellite TV systems. BER vs Bit/Noise ratio should be

simulated for BER 10-2 and 10-3

for computer generated Additive White Noise with uniform probability density

function

19. 1904633

P a g e | 4

Analysis and simulation of a communication system with Differential Binary Phase Shift Keying (DBPSK)

modulation. BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive

White Gaussian Noise without pulse shaping. Bit rate 4.8 Kbit/s

20. 1922963

Analysis and simulation of a communication system with Binary Amplitude Shift Keying (ASK) modulation and

coherent signal processing. BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer

generated Additive White Gaussian Noise without pulse shaping. Bit rate 128 Kbit/s

21. 1800899

Analysis and simulation of one channel of Bluetooth wireless connection. BER vs Bit/Noise ratio should be

simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise.

22. 1896859

Analysis and simulation of a communication system with Quadrature Amplitude Modulation (QAM) M=32. BER vs

Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise.

Bit rate 32 Kbit/s.

23. NON – see example

Analysis and simulation of a communication system with Binary Amplitude Shift Keying (ASK) modulation and

non-coherent (post detector) signal processing. BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise without pulse shaping. Bit rate 64 Kbit/s

24. 1721956

Analysis and modelling of a baseband communication system with Manchester - 2 coding – decoding. By means

of computer simulation evaluate the BER for computer generated Additive White Noise with uniform probability

density function. Data rate 1028 Kbit/s.

25. 1892829

Analysis and modelling of a baseband communication system with Manchester - 1 coding – decoding. By means

of computer simulation evaluate the BER for computer generated Additive White Gaussian Noise. Data rate 4.8

Kbit/s.

26. 1967052

Analysis and simulation of one channel (satellite to ground) in Inmarsat Satellite mobile communication system

IRIDIUM. BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive

White Gaussian Noise

27. 1902931

Analysis and simulation of one channel of Bluetooth transceivers. BER vs Bit/Noise ratio should be simulated for

BER 10-2

to 10-3

for computer generated Additive White Gaussian Noise.

28 1917093

Analysis and simulation of a communication system with 8-ary Phase Shift Keying (PSK) modulation. BER vs

Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise.

Bit rate 32 Kbit/s.

29 1897594

Analysis and simulation of a communication system with 16-ary Quadrature Amplitude Modulation (QAM). BER vs

Bit/Noise ratio should be analytically obtained and be simulated for BER 10-3

for computer generated Additive

White Gaussian Noise; 4 M samples per second. It shall be generated the noise and shown its characteristics in

P a g e | 5

time and frequency domain at the input and output of matched filter. In addition the simulated 16-ary QAM signal

in time and frequency domain shall be shown for the sequence 1100 0101 0010 1101 0101 0000 1100.

30 1883446

Analysis and modelling of a baseband communication system with Manchester - 2 coding – decoding. By means

of computer simulation evaluate the BER (10-3 – 10-4

) for computer generated Additive White Gaussian Noise.

Data rate 256 Kbit/s.

31 1891833

Analysis and simulation of a communication system with Quadrature Amplitude Modulation (QAM) M=64. BER vs

Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive White Gaussian Noise.

Bit rate 2048 Kbit/s.

32 1934273

Analysis and simulation of a communication system with π/2 Quadrature Phase Shift Keying (π/2-QPSK)

modulation. BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive

White Gaussian Noise without pulse shaping. Bit rate 1024 Kbit/s

33 1896155

Analysis and simulation of a communication system with Gaussian Minimum Shift Keying (GMSK). BER vs

Bit/Noise ratio should be analytically obtained and be simulated for BER 10-3

for computer generated Additive

White Gaussian Noise. It shall be generated the noise and shown its characteristics in time and frequency domain

at the input and output of matched filter. In addition the simulated GMSK signal in time and frequency domain

shall be shown for the sequence 1000 0101 1110 1101 0101 0101 1101.

34 1894313

Analysis and simulation of a communication system with Differential Binary Phase Shift Keying (DBPSK)

modulation. BER vs Bit/Noise ratio should be simulated for BER 10-2 and 10-3

for computer generated Additive

White Gaussian Noise without pulse shaping. Bit rate 64 Kbit/s. In addition the simulated DBPSK signal in time

and frequency domain shall be shown for the sequence 1110 1101 0101 0101 1101 1010 0001 1110.

35 1974007

Comparative analysis of spectrum and waveforms (time domain) of Binary Phase Shift Keying (BPSK) and Offset

Quadrature Shift Keying (QPSK) modulations. It shall be estimated BER vs Bit/Noise ratio computer simulated

for BER 10-3

for computer generated Additive White Gaussian Noise.

36 1903035

Analysis and simulation and of one channel of Direct Satellite TV systems. BER vs Bit/Noise ratio should be

simulated for BER 10-2 and 10-3

for computer generated Additive White Noise with Gaussian probability density

function and data rate 1,200 Kbit/sec

37 1874515

Analysis and simulation of a communication system with Code Division Multiple Access (CDMA). Simulate signal

reception at a background of N interferences using M-sequences for signal spreading with the length M=4,095.

BER vs N (Number of Interferences) should be simulated for BER 10-2 for computer generated M-sequences,

presumably 8<N<64

38 1934982

Analysis and simulation of a communication system with Binary Amplitude Shift Keying (ASK) and Raised Cosine

Rolloff Filter modulation (with α factor 0, 0.5 and 1) and coherent signal processing. BER vs Bit/Noise ratio

P a g e | 6

should be simulated for BER 10-2

for computer generated Additive White Gaussian Noise without pulse shaping.

Bit rate 32 Kbit/s

39

Analysis and simulation of one channel of Bluetooth transceivers. BER vs Bit/Noise ratio should be simulated for

BER 10-2

for computer generated Additive White Gaussian Noise. Generate and show in time (waveform) and

frequency (spectrum) domain this signal for the code: 1110 1101 0101 0101 1101 1010 0001 1110.

P a g e | 7

Section 3.

Example of the contents:

Typical example of an essay topic – "Analysis and simulation of communication system with Amplitude

Shift Keying modulation", which may include:

1. Definition of ASK and an area of applications

2. Analytical equations which describe ASK signal

3. Definition of baseband and bandpass signals in the system.

4. The modulation and demodulation processes description.

5. Examples of ASK signal with time domain and frequency domain presentations

6. Analytical equations which describe BER in ASK based systems.

7. Calculations of BER using the equations

8. Signal modelling (Signal generation using computer).

9. Show the signal waveform and spectrum

10. Noise modelling (Gaussian noise generation using computer).

11. Show the noise Power Spectral Density (PSD)

12. Signal and noise processing in the demodulator (with matched filter)

13. BER modelling for 10-2 and 10-3

14. Comparisons of modelling (m) and calculation (g) results

15. Conclusions

This is an example only!!! Students should not expect any detailed instruction and are free how

to present the specified problem.

P a g e | 8

Section 4.

Template: (one column!) of the MSc assignment "Communication Signal Processing" – Principles of

communications, corresponds to the template of papers submission to IEEE transactions journal.

Abstract—(Arial 9) These instructions give you guidelines for preparing papers for IEEE TRANSACTIONS and JOURNALS. Use

this document as a template if you are using Microsoft Word 6.0 or later. Otherwise, use this document as an instruction set. The

electronic file of your paper will be formatted further at IEEE. Define all symbols used in the abstract. Do not cite references in the

abstract. Do not delete the blank line immediately above the abstract; it sets the footnote at the bottom of this column.

Keywords – (Arial 9) e.g. communication systems, bit error rate, etc.

I Introduction (from this point all the text body is in Aerial 10, titles Aerial 11, bold, subtitles Aerial 11,

Italic )

HIS document is a template for Microsoft Word versions 6.0 or later.

If your paper is intended for a conference, please contact your conference editor concerning acceptable word

processor formats for your particular conference. When you open TRANS-JOUR.DOC, select “Page Layout” from the

“View” menu in the menu bar (View | Page Layout), which allows you to see the footnotes. Then, type over sections of

TRANS-JOUR.DOC or cut and paste from another document and use markup styles. The pull-down style menu is at the

left of the Formatting Toolbar at the top of your Word window (for example, the style at this point in the document is

“Text”). Highlight a section that you want to designate with a certain style, then select the appropriate name on the style

menu. The style will adjust your fonts and line spacing. Do not change the font sizes or line spacing to squeeze more

text into a limited number of pages. Use italics for emphasis; do not underline.

To insert images in Word, position the cursor at the insertion point and either use Insert | Picture | From File or copy the

image to the Windows clipboard and then Edit | Paste Special | Picture (with “float over text” unchecked).

All pages should be numerated starting with "1".

II Procedure for the submission

A. Figures

Format and save your graphic images using a suitable graphics processing program that will allow you to create the

images as PostScript (PS), Encapsulated PostScript (EPS), or Tagged Image File Format (TIFF), sizes them, and adjusts

the resolution settings. If you created your source files in one of the following you will be able to submit the graphics

without converting to a PS, EPS, or TIFF file: Microsoft Word, Microsoft PowerPoint, Microsoft Excel, or Portable

Document Format (PDF).

III Electronic Image Files (Optional)

Import your source files in one of the following: Microsoft Word, Microsoft PowerPoint, Microsoft Excel, or Portable

Document Format (PDF); you will be able to submit the graphics without converting to a PS, EPS, or TIFF files. Image

Manuscript received October 9, 2001. (Write the date on which you submitted your paper for review.) This work was supported in part by the U.S. Department of

Commerce under Grant BS123456 (sponsor and financial support acknowledgment goes here). Paper titles should be written in uppercase and lowercase letters, not all

uppercase. Avoid writing long formulas with subscripts in the title; short formulas that identify the elements are fine (e.g., "Nd–Fe–B"). Do not write “(Invited)” in the

title. Full names of authors are preferred in the author field, but are not required. Put a space between authors’ initials.

F. A. Author is with the National Institute of Standards and Technology, Boulder, CO 80305 USA (corresponding author to provide phone: 303-555-5555; fax: 303-

555-5555; e-mail: author@ boulder.nist.gov).

S. B. Author, Jr., was with Rice University, Houston, TX 77005 USA. He is now with the Department of Physics, Colorado State University, Fort Collins, CO 80523

USA (e-mail: author@lamar.colostate.edu).

T. C. Author is with the Electrical Engineering Department, University of Colorado, Boulder, CO 80309 USA, on leave from the National Research Institute for

Metals, Tsukuba, Japan (e-mail: author@nrim.go.jp).

ASSIGNMENT TITLE

Student name, ID number and the date of submission

T

P a g e | 9

quality is very important to how yours graphics will reproduce. Even though we can accept graphics in many formats, we

cannot improve your graphics if they are poor quality when we receive them. If your graphic looks low in quality on your

printer or monitor, please keep in mind that cannot improve the quality after submission.

If you are importing your graphics into this Word template, please use the following steps:

Under the option EDIT select PASTE SPECIAL. A dialog box will open, select paste picture, then click OK. Your figure

should now be in the Word Document.

If you are preparing images in TIFF, EPS, or PS format, note the following. High-contrast line figures and tables should

be prepared with 600 dpi resolution and saved with no compression, 1 bit per pixel (monochrome), with file names in the

form of “fig3.tif” or “table1.tif.”

Photographs and grayscale figures should be prepared with 300 dpi resolution and saved with no compression, 8 bits

per pixel (grayscale).

A. Sizing of Graphics

Most charts graphs and tables are one column wide (3 1/2 inches or 21 picas) or two-column width (7 1/16 inches, 43

picas wide). We recommend that you avoid sizing figures less than one column wide, as extreme enlargements may

distort your images and result in poor reproduction. Therefore, it is better if the image is slightly larger, as a minor

reduction in size should not have an adverse affect the quality of the image.

B. Size of Author Photographs (Compulsory for all students)

The final printed size of an author photograph is exactly 1 inch wide by 1 1/4 inches long (6 picas × 7 1/2 picas). Please

ensure that the author photographs you submit are proportioned similarly. If the author’s photograph does not appear at

the end of the paper, then please size it so that it is proportional to the standard size of 1 9/16 inches wide by 2 inches

long (9 1/2 picas × 12 picas). JPEG files are only accepted for author photos.

C. How to create a PostScript File

First, download a PostScript printer driver from http://www.adobe.com/support/downloads/pdrvwin.htm (for Windows) or

from http://www.adobe.com/support/downloads/ pdrvmac.htm (for Macintosh) and install the “Generic PostScript Printer”

definition. In Word, paste your figure into a new document. Print to a file using the PostScript printer driver. File names

should be of the form “fig5.ps.” Use Open Type fonts when creating your figures, if possible. A listing of the acceptable

fonts are as follows: Open Type Fonts: Times Roman, Helvetica, Helvetica Narrow, Courier, Symbol, Palatino, Avant

Garde, Bookman, Zapf Chancery, Zapf Dingbats, and New Century Schoolbook.

D. Print Color Graphics Requirements

IEEE accepts color graphics in the following formats: EPS, PS, TIFF, Word, PowerPoint, Excel, and PDF. The

resolution of a RGB color TIFF file should be 400 dpi.

When sending color graphics, please supply a high quality hard copy or PDF proof of each image. If we cannot achieve

a satisfactory color match using the electronic version of your files, we will have your hard copy scanned. Any of the files

types you provide will be converted to RGB color EPS files.

E. Web Color Graphics

IEEE accepts color graphics in the following formats: EPS, PS, TIFF, Word, PowerPoint, Excel, and PDF. The

resolution of a RGB color TIFF file should be at least 400 dpi.

Your color graphic will be converted to grayscale if no separate grayscale file is provided. If a graphic is to appear in

print as black and white, it should be saved and submitted as a black and white file. If a graphic is to appear in print or on

IEEE Xplore in color, it should be submitted as RGB color.

F. Graphics Checker Tool

The IEEE Graphics Checker Tool enables users to check graphic files. The tool will check journal article graphic files

against a set of rules for compliance with IEEE requirements. These requirements are designed to ensure sufficient

image quality so they will look acceptable in print. After receiving a graphic or a set of graphics, the tool will check the

files against a set of rules. A report will then be e-mailed listing each graphic and whether it met or failed to meet the

requirements. If the file fails, a description of why and instructions on how to correct the problem will be sent. The IEEE

Graphics Checker Tool is available at http://graphicsqc.ieee.org/

For more Information, contact the IEEE Graphics H-E-L-P Desk by e-mail at graphics@ieee.org. You will then receive

an e-mail response and sometimes a request for a sample graphic for us to check.

IV MATH

If you are using Word, use either the Microsoft Equation Editor or the MathType add-on (http://www.mathtype.com) for

P a g e | 10

equations in your paper (Insert | Object | Create New | Microsoft Equation or MathType Equation). “Float over text” should

not be selected.

V Units

Use either SI (MKS) or CGS as primary units. (SI units are strongly encouraged.) English units may be used as

secondary units (in parentheses). This applies to papers in data storage. For example, write “15 Gb/cm2

(100 Gb/in2

).”

An exception is when English units are used as identifiers in trade, such as “3-in disk drive.” Avoid combining SI and

CGS units, such as current in amperes and magnetic field in oersteds. This often leads to confusion because equations

do not balance dimensionally. If you must use mixed units, clearly state the units for each quantity in an equation.

The SI unit for magnetic field strength H is A/m. However, if you wish to use units of T, either refer to magnetic flux

density B or magnetic field strength symbolized as μ0H. Use the center dot to separate compound units, e.g., “A·m2

.”

VI Helpful Hints

A. Figures and Tables

Because IEEE will do the final formatting of your paper, you do not need to position figures and tables at the top and

bottom of each column. In fact, all figures, figure captions, and tables can be at the end of the paper. Large figures and

tables may span both columns. Place figure captions below the figures; place table titles above the tables. If your figure

has two parts, include the labels “(a)” and “(b)” as part of the artwork. Please verify that the figures and tables you mention

in the text actually exist. Please do not include captions as part of the figures. Do not put captions in “text boxes”

linked to the figures. Do not put borders around the outside of your figures. Use the abbreviation “Fig.” even at the

beginning of a sentence. Do not abbreviate “Table.” Tables are numbered with Roman numerals.

Color printing of figures is available, but is billed to the authors. Include a note with your final paper indicating that you

request and will pay for color printing. Do not use color unless it is necessary for the proper interpretation of your figures.

If you want reprints of your color article, the reprint order should be submitted promptly. There is an additional charge for

color reprints. Please note that many IEEE journals now allow an author to publish color figures on Xplore and

black and white figures in print. Contact your society representative for specific requirements.

Figure axis labels are often a source of confusion. Use words rather than symbols. As an example, write the quantity

“Magnetization,” or “Magnetization M,” not just “M.” Put units in parentheses. Do not label axes only with units. As in Fig.

1, for example, write “Magnetization (A/m)” or “Magnetization (A

m1

),” not just “A/m.” Do not label axes with a ratio of

quantities and units. For example, write “Temperature (K),” not “Temperature/K.”

Multipliers can be especially confusing. Write “Magnetization (kA/m)” or “Magnetization (103 A/m).” Do not write

“Magnetization (A/m) ? 1000” because the reader would not know whether the top axis label in Fig. 1 meant 16000 A/m or

0.016 A/m. Figure labels should be legible, approximately 8 to 12 point type.

B. References

Number citations consecutively in square brackets [1]. The sentence punctuation follows the brackets [2]. Multiple

references [2], [3] are each numbered with separate brackets [1]–[3]. When citing a section in a book, please give the

relevant page numbers [2]. In sentences, refer simply to the reference number, as in [3]. Do not use “Ref. [3]” or

“reference [3]” except at the beginning of a sentence: “Reference [3] shows ... .” Please do not use automatic endnotes in

Word, rather, type the reference list at the end of the paper using the “References” style.

Number footnotes separately in superscripts (Insert | Footnote).1 Place the actual footnote at the bottom of the column

in which it is cited; do not put footnotes in the reference list (endnotes). Use letters for table footnotes (see Table I).

Please note that the references at the end of this document are in the preferred referencing style. Give all authors’

names; do not use “et al.” unless there are six authors or more. Use a space after authors’ initials. Papers that have not

been published should be cited as “unpublished” [4]. Papers that have been accepted for publication, but not yet specified

for an issue should be cited as “to be published” [5]. Papers that have been submitted for publication should be cited as

“submitted for publication” [6]. Please give affiliations and addresses for private communications [7].

Capitalize only the first word in a paper title, except for proper nouns and element symbols. For papers published in

translation journals, please give the English citation first, followed by the original foreign-language citation [8].

C. Abbreviations and Acronyms

Define abbreviations and acronyms the first time they are used in the text, even after they have already been defined in

the abstract. Abbreviations such as IEEE, SI, ac, and dc do not have to be defined. Abbreviations that incorporate periods

should not have spaces: write “C.N.R.S.,” not “C. N. R. S.” Do not use abbreviations in the title unless they are

1

It is recommended that footnotes be avoided (except for the unnumbered footnote with the receipt date on the first page). Instead, try to integrate the footnote

information into the text.

P a g e | 11

unavoidable (for example, “IEEE” in the title of this article).

D Equations

Number equations consecutively with equation numbers in parentheses flush with the right margin, as in (1). First use

the equation editor to create the equation. Then select the “Equation” markup style. Press the tab key and write the

equation number in parentheses. To make your equations more compact, you may use the solidus ( / ), the exp function,

or appropriate exponents. Use parentheses to avoid ambiguities in denominators. Punctuate equations when they are part

of a sentence, as in

exp( | |) ( ) ( ) .

( , ) [ /(2 )]

(1)

Be sure that the symbols in your equation have been defined before the equation appears or immediately following.

Italicize symbols (T might refer to temperature, but T is the unit tesla). Refer to “(1),” not “Eq. (1)” or “equation (1),” except

at the beginning of a sentence: “Equation (1) is ... .”

VII Other Recommendations

Use one space after periods and colons. Hyphenate complex modifiers: “zero-field-cooled magnetization.” Avoid

dangling participles, such as, “Using (1), the potential was calculated.” [It is not clear who or what used (1).] Write instead,

“The potential was calculated by using (1),” or “Using (1), we calculated the potential.”

Use a zero before decimal points: “0.25,” not “.25.” Use “cm3

,” not “cc.” Indicate sample dimensions as “0.1 cm 0.2

cm,” not “0.1 0.2 cm2

.” The abbreviation for “seconds” is “s,” not “sec.” Do not mix complete spellings and abbreviations

of units: use “Wb/m2

” or “webers per square meter,” not “webers/m2

.” When expressing a range of values, write “7 to 9” or

“7-9,” not “7~9.”

A parenthetical statement at the end of a sentence is punctuated outside of the closing parenthesis (like this). (A

parenthetical sentence is punctuated within the parentheses.) In American English, periods and commas are within

quotation marks, like “this period.” Other punctuation is “outside”! Avoid contractions; for example, write “do not” instead of

“don’t.” The serial comma is preferred: “A, B, and C” instead of “A, B and C.”

If you wish, you may write in the first person singular or plural and use the active voice (“I observed that ...” or “We

observed that ...” instead of “It was observed that ...”). Remember to check spelling. If your native language is not English,

please get a native English-speaking colleague to carefully proofread your paper.

VIII Some Common Mistakes

The word “data” is plural, not singular. The subscript for the permeability of vacuum μ0 is zero, not a lowercase letter

“o.” The term for residual magnetization is “remanence”; the adjective is “remanent”; do not write “remnance” or “remnant.”

Use the word “micrometer” instead of “micron.” A graph within a graph is an “inset,” not an “insert.” The word

“alternatively” is preferred to the word “alternately” (unless you really mean something that alternates). Use the word

“whereas” instead of “while” (unless you are referring to simultaneous events). Do not use the word “essentially” to mean

“approximately” or “effectively.” Do not use the word “issue” as a euphemism for “problem.” When compositions are not

specified, separate chemical symbols by en-dashes; for example, “NiMn” indicates the intermetallic compound Ni0.5Mn0.5

whereas “Ni–Mn” indicates an alloy of some composition NixMn1-x.

Be aware of the different meanings of the homophones “affect” (usually a verb) and “effect” (usually a noun),

“complement” and “compliment,” “discreet” and “discrete,” “principal” (e.g., “principal investigator”) and “principle” (e.g.,

“principle of measurement”). Do not confuse “imply” and “infer.”

Prefixes such as “non,” “sub,” “micro,” “multi,” and “ultra” are not independent words; they should be joined to the words

they modify, usually without a hyphen. There is no period after the “et” in the Latin abbreviation “et al.” (it is also italicized).

The abbreviation “i.e.,” means “that is,” and the abbreviation “e.g.,” means “for example” (these abbreviations are not

italicized).

An excellent style manual and source of information for science writers is [9]. A general IEEE style guide and an

Information for Authors are both available at http://www.ieee.org/web/publications/authors/transjnl/index.html

IX Publication Principles

The contents of IEEE TRANSACTIONS and JOURNALS are peer-reviewed and archival. The TRANSACTIONS publishes

scholarly articles of archival value as well as tutorial expositions and critical reviews of classical subjects and topics of

current interest.

P a g e | 12

Authors should consider the following points:

1) Technical papers submitted for publication must advance the state of knowledge and must cite relevant prior work.

2) The length of a submitted paper should be commensurate with the importance, or appropriate to the complexity, of the

work. For example, an obvious extension of previously published work might not be appropriate for publication or

might be adequately treated in just a few pages.

3) Authors must convince both peer reviewers and the editors of the scientific and technical merit of a paper; the

standards of proof are higher when extraordinary or unexpected results are reported.

4) Because replication is required for scientific progress, papers submitted for publication must provide sufficient

information to allow readers to perform similar experiments or calculations and use the reported results. Although not

everything need be disclosed, a paper must contain new, useable, and fully described information. For example, a

specimen’s chemical composition need not be reported if the main purpose of a paper is to introduce a new

measurement technique. Authors should expect to be challenged by reviewers if the results are not supported by

adequate data and critical details.

5) Papers that describe ongoing work or announce the latest technical achievement, which are suitable for presentation

at a professional conference, may not be appropriate for publication in a TRANSACTIONS or JOURNAL.

X Conclusion

A conclusion section is not required. Although a conclusion may review the main points of the paper, do not replicate

the abstract as the conclusion. A conclusion might elaborate on the importance of the work or suggest applications and

extensions.

APPENDIX

Appendixes, if needed, appear before the acknowledgment.

ACKNOWLEDGMENT

The preferred spelling of the word “acknowledgment” in American English is without an “e” after the “g.” Use the

singular heading even if you have many acknowledgments. Avoid expressions such as “One of us (S.B.A.) would like to

thank ... .” Instead, write “F. A. Author thanks ... .” Sponsor and financial support acknowledgments are placed in the

unnumbered footnote on the first page, not here.

REFERENCES

[1] G. O. Young, “Synthetic structure of industrial plastics (Book style with paper title and editor),” in Plastics, 2nd ed. vol. 3, J. Peters, Ed. New

York: McGraw-Hill, 1964, pp. 15–64.

[2] W.-K. Chen, Linear Networks and Systems (Book style). Belmont, CA: Wadsworth, 1993, pp. 123–135.

[3] H. Poor, An Introduction to Signal Detection and Estimation. New York: Springer-Verlag, 1985, ch. 4.

[4] B. Smith, “An approach to graphs of linear forms (Unpublished work style),” unpublished.

[5] E. H. Miller, “A note on reflector arrays (Periodical style—Accepted for publication),” IEEE Trans. Antennas Propagat., to be published.

[6] J. Wang, “Fundamentals of erbium-doped fiber amplifiers arrays (Periodical style—Submitted for publication),” IEEE J. Quantum Electron.,

submitted for publication.

[7] C. J. Kaufman, Rocky Mountain Research Lab., Boulder, CO, private communication, May 1995.

[8] Y. Yorozu, M. Hirano, K. Oka, and Y. Tagawa, “Electron spectroscopy studies on magneto-optical media and plastic substrate interfaces

(Translation Journals style),” IEEE Transl. J. Magn.Jpn., vol. 2, Aug. 1987, pp. 740–741 [Dig. 9th Annu. Conf. Magnetics Japan, 1982, p. 301].

[9] M. Young, The Technical Writers Handbook. Mill Valley, CA: University Science, 1989.

[10] J. U. Duncombe, “Infrared navigation—Part I: An assessment of feasibility (Periodical style),” IEEE Trans. Electron Devices, vol. ED-11, pp. 34–39,

Jan. 1959.

[11] S. Chen, B. Mulgrew, and P. M. Grant, “A clustering technique for digital communications channel equalization using radial basis function

networks,” IEEE Trans. Neural Networks, vol. 4, pp. 570–578, Jul. 1993.

[12] R. W. Lucky, “Automatic equalization for digital communication,” Bell Syst. Tech. J., vol. 44, no. 4, pp. 547–588, Apr. 1965.

[13] S. P. Bingulac, “On the compatibility of adaptive controllers (Published Conference Proceedings style),” in Proc. 4th Annu. Allerton Conf. Circuits

and Systems Theory, New York, 1994, pp. 8–16.

[14] G. R. Faulhaber, “Design of service systems with priority reservation,” in Conf. Rec. 1995 IEEE Int. Conf. Communications, pp. 3–8.

[15] W. D. Doyle, “Magnetization reversal in films with biaxial anisotropy,” in 1987 Proc. INTERMAG Conf., pp. 2.2-1–2.2-6.

[16] G. W. Juette and L. E. Zeffanella, “Radio noise currents n short sections on bundle conductors (Presented Conference Paper style),”

presented at the IEEE Summer power Meeting, Dallas, TX, Jun. 22–27, 1990, Paper 90 SM 690-0 PWRS.

[17] J. G. Kreifeldt, “An analysis of surface-detected EMG as an amplitude-modulated noise,” presented at the 1989 Int. Conf. Medicine and Biological

Engineering, Chicago, IL.

[18] J. Williams, “Narrow-band analyzer (Thesis or Dissertation style),” Ph.D. dissertation, Dept. Elect. Eng., Harvard Univ., Cambridge, MA, 1993.

[19] N. Kawasaki, “Parametric study of thermal and chemical nonequilibrium nozzle flow,” M.S. thesis, Dept. Electron. Eng., Osaka Univ., Osaka, Japan,

1993.

P a g e | 13

[20] J. P. Wilkinson, “Nonlinear resonant circuit devices (Patent style),” U.S. Patent 3 624 12, July 16, 1990.

[21] IEEE Criteria for Class IE Electric Systems (Standards style), IEEE Standard 308, 1969.

[22] Letter Symbols for Quantities, ANSI Standard Y10.5-1968.

[23] R. E. Haskell and C. T. Case, “Transient signal propagation in lossless isotropic plasmas (Report style),” USAF Cambridge Res. Lab., Cambridge,

MA Rep. ARCRL-66-234 (II), 1994, vol. 2.

[24] E. E. Reber, R. L. Michell, and C. J. Carter, “Oxygen absorption in the Earth’s atmosphere,” Aerospace Corp., Los Angeles, CA, Tech. Rep. TR-

0200 (420-46)-3, Nov. 1988.

[25] (Handbook style) Transmission Systems for Communications, 3rd ed., Western Electric Co., Winston-Salem, NC, 1985, pp. 44–60.

[26] Motorola Semiconductor Data Manual, Motorola Semiconductor Products Inc., Phoenix, AZ, 1989.

[27] (Basic Book/Monograph Online Sources) J. K. Author. (year, month, day). Title (edition) [Type of medium]. Volume (issue). Available:

http://www.(URL)

[28] J. Jones. (1991, May 10). Networks (2nd ed.) [Online]. Available: http://www.atm.com

[29] (Journal Online Sources style) K. Author. (year, month). Title. Journal [Type of medium]. Volume(issue), paging if given. Available:

http://www.(URL)

[30] R. J. Vidmar. (1992, August). On the use of atmospheric plasmas as electromagnetic reflectors. IEEE Trans. Plasma Sci. [Online]. 21(3). pp. 876–

880. Available: http://www.halcyon.com/pub/journals/21ps03-vidmar

First A. Author (M’76–SM’81–F’87) and the other authors may include biographies at the end of regular

papers. Biographies are often not included in conference-related papers. This author became a Member

(M) of IEEE in 1976, a Senior Member (SM) in 1981, and a Fellow (F) in 1987. The first paragraph may

contain a place and/or date of birth (list place, then date). Next, the author’s educational background is

listed. The degrees should be listed with type of degree in what field, which institution, city, state, and

country, and year degree was earned. The author’s major field of study should be lower-cased.

The second paragraph uses the pronoun of the person (he or she) and not the author’s last

name. It lists military and work experience, including summer and fellowship jobs. Job titles are

capitalized. The current job must have a location; previous positions may be listed without one.

Information concerning previous publications may be included. Try not to list more than three books or

published articles. The format for listing publishers of a book within the biography is: title of book (city,

state: publisher name, year) similar to a reference. Current and previous research interests end the

paragraph.

The third paragraph begins with the author’s title and last name (e.g., Dr. Smith, Prof. Jones,

Mr. Kajor, Ms. Hunter). List any memberships in professional societies other than the IEEE. Finally, list

any awards and work for IEEE committees and publications. If a photograph is provided, the biography

will be indented around it. The photograph is placed at the top left of the biography. Personal hobbies

will be deleted from the biography.

PHOTO

The photo is

not

compulsory.

P a g e | 14

30059 Section 5.

Digital communication and signal processing

Prof M Cherniakov and Prof M Gashinova

Student: Mark Max

Demonstration of the problem and the concept understanding as a part of the broader

concept of Digital Communication. Ability to specify the problem and define the proper

way of the problem investigation

20

18

16

14

12

10

8

6

4

2

Distinct.

Merit

Pass

Fail

/ 20

Creativity of the material presentation, i.e. original approach, graphs, figures,

examples, etc. Understanding of how to select a proper literature and use of the

literature.

Distinct.

Merit

Pass

Fail

/ 20

Proper and clear explanation and presentation of the specified problem.

Technical communication skills, i.e. clarity of the mathematical presentation, the

introduction and conclusion of arguments, correspondence to the recommended to

the assignment template.

Distinct.

Merit

Pass

Fail

/ 20

Demonstration of computer modelling skills, that include the model flow chart,

language (software package) selection and the modelling simulation skills application

to the given problem solution

Distinct.

Merit

Pass

Fail

/ 20

Ability to draw and clearly formulate conclusions which are essentially based on the

results comparison with the known from literature as well as the results

correspondence to general knowledge obtained by the students from the lecture

course as well as other related disciplines.

Distinct.

Merit

Pass

Fail

/ 20

Marker name: Professor M. Cherniakov / M. Gashinova December 2018

/100

Any evidence of plagiarism YES NO

Comments:

P a g e | 15

Good Practice

Example of a similar assignment but not for Communication

Signal Processing

This is an example how the essay shall look like

NON-COHERENT BINARY ASK COMMUNICATION SYSTEM

Abstract— This report demonstrates a non-coherent binary amplitude shift keying communication system with a data rate

of 64Kbps. In detailed analysis of binary ASK system is presented followed by the design, simulation and modelling of the

system in MATLAB and Simulink. To observe the effect of variable channel noise in the overall performance of system,

designed model is simulated in the presence of AWGN with an Eb/ No of 1-15dB. Noise analysis has also been performed to

demonstrate the parameters of white Gaussian noise. Comparison between simulation results and theoretical results show

that the designed system performs well in the presence of AWGN noise.

Keywords – binary ASK, non-coherent, BER, AWGN, digital modulation

I. INTRODUCTION

Digital modulation is advantageous over the analog counterpart because of its high noise immunity, high spectral

efficiency, efficient multiplexing, software implementation and greater security.

Basic aim of this research is to demonstrate a binary amplitude shift keying (BASK) communication system in the

medium with an additive white Gaussian noise having various values of Eb/No (Energy per bit to noise power) thereby,

demonstrating the variation in BER with Eb/No as the BASK signal propagates.

BASK is digital modulation technique in which, data communication is performed using two amplitude levels i.e. 1 and

0. The carrier is transmitted when the bit is 1 whereas, no transmission is done for bit 0. As the modulated signal is

transmitted through the medium, the effect of channel noise is introduced in the transmitted signal. BASK modulation

scheme is comparatively simpler in comparison to other digital modulation schemes; therefore, the effect is channel noise

is prominent. Because of this, the bit error rate for a binary amplitude shift keying system is more in comparison to FSK,

PSK, QAM modulation schemes. Due to an intrinsic high bit error rate (BER), when a BASK system is designed, it is

essential to have an efficient detection of the input bits at the receiver due to the effect of a dominant channel noise.

In the designed system, to pass the required signal bandwidth and to limit the channel noise (AWGN) bandwidth, a

band-pass and a low-pass filter is used in first stage of receiver. BPF suppresses AWGN at the receiver thereby,

improving the overall bit error rate. Whereas the LPF is used for envelop detection. The designed LPF has a cut off

frequency of 5Hz with an out of band rejection of 30dB. If the cutoff frequency is reduced, the performance of LPF in

suppressing the noise enhances. However, there is a practical limitation on the cut off frequency of a LPF because of

which, the frequency cannot be further reduced from 5Hz. Sampling frequency also affects the performance of filter. The

higher the sampling frequency, better is the performance of filter in terms of noise removal. However, there is again a limit

up to how much the sampling frequency of filter can be increased. Higher sampling frequency makes the overall design of

communication system complex. In the designed filter for the BASK system, sampling frequency is set at 100Hz.

P a g e | 16

Generic block level diagram of ASK communication system in Figure 1 consists of a transmitter where BASK

modulation is performed on the input bit stream, a transmission medium where noise is added to the system and a

receiver where demodulation is performed to retrieve the transmitter bit stream. Comparison of transmitted and detected

bit stream of performed to determine the BER.

II. LITERATURE REVIEW

A. Digital Modulation

Modulation is a process in which the information from source is encoded by up converting it to a band pass signal with

a frequency higher than the baseband signal. Modulation is performed by translating or keying the amplitude, frequency or

phase of the carrier having higher frequency according to the amplitude of baseband signal. To extract baseband signal

from the continuous carrier signal, demodulation is performed.

B. Digital Modulation Schemes

Different types of digital modulation schemes are shown in Figure 2.

C. Maximum Data Rate

The maximum possible data rate in any transmission medium is given by Shannon’s channel capacity equation [1].

(1)

Where,

C= Channel Capacity in bps

B= Signal Bandwidth

S/N= Signal to noise ratio

D. Binary Amplitude Shift Keying

Figure 1: Block Diagram of a generic Binary ASK Communication System

Figure 2: Types of Digital Modulation Schemes

P a g e | 17

BASK commonly known as on-off keying (OOK) is modulation scheme in which a digital signal is expressed as carrier

amplitude’s variation. It is narrow band modulation in which amplitude of a continuous high frequency carrier is varied

according to amplitude of input binary data.

i.Modulation

In ASK system, baseband information is unipolar binary data with information as 0’s and 1’s. Bit 1 is transmitted with a

high frequency carrier whereas for bit 0 no transmission is done. ASK waveform can be mathematically represented as:

(2)

The input bit stream with 16 symbols, sinosoidal carrier and ASK modulated signal to be transmitted is shown in Figure

3.

ii.Transmission Medium

Transmission medium constitutes of various types of noise, which affects the modulated signal. If the strength of noise

if large, received signal is corrupted thereby, giving errors. There are different types of noise as shown below.

Band limited white noise

The PSD of this noise is constant over the defined bandwidth. The signal is corrupted when noise level is greater than

the decision threshold leading to bit error.

Additive White Gaussian Noise

AWGN replicates the effect of random processes occurring in the medium.

o Additive: Noise is added to the transmitted signal

o White: Flat spectrum for all frequencies

o Gaussian: Noise follows Gaussian probability distribution [2]

Figure 3: Input bit stream, carrier signal and BASK modulated signal

P a g e | 18

(3)

With μ=0 and

iii. Demodulation

Received signal can now be represented as:

Rx = Tx + No (4)

Where,

Rx = Received signal

Tx = Transmitted modulated signal

No = Channel noise

Demodulator reduces the channel corrupted waveform to a series of symbols which estimates the transmitted data

bits. On the basis of a threshold, it maps the received signal to digital bits. Demodulator only needs to determine the

presence or absence of carrier therefore, it’s a simple process. Signal detection is of two main types [3]:

Coherent Detection (Synchronous Detection)

o Receiver’s carrier and transmitter carrier are phase locked

o Correlation between received noisy signal and locally generated signal detects the transmitted signal

o Expensive and complex carrier recovery required

o Improved BER

Non-coherent Detection (Asynchronous Detection)

o Phase locking not required between transmitter and receiver carrier

o Simpler signal recovery process

o High probability of BER

E. Bit error rate (BER)

It is the ratio of total error bits and the transmitted bits, affected by the following factors:

o Channel noise

o Inter symbol interference

o Distortion

o Bit synchronization

o Signal attenuation

o Multi path Fading

BER is expressed as normalized signal to noise ratio or Eb/No. BER vs SNR (Eb/No) curves are plotted to express the

performance of a digital system.

The received signal is represented by:

Y=s1+n : bit 1 transmitted (s1=1)

Y=so+n : bit 1 transmitted (so=0)

P a g e | 19

The two conditional probabilities for bit detection can be represented by [4]:

(5)

(6)

If magnitude of received signal Y is greater than the threshold, the detected bit is 1 whereas, if the magnitude of

received signal Y is less than threshold, it is expected that the transmitted bit is 0. The amplitude of modulated symbol is

represented as:

Hence,

(7)

(8)

The signal space of binary ASK system is in single dimension.

The distance between two signal points is represented by:

Therefore, the probability of error is:

BER of non-coherent ASK is mathematically represented as [5]:

(9)

BER of coherent ASK is mathematically represented as:

(10)

F. BASK Constellation Diagram

P a g e | 20

Constellation diagram of an ASK signal can be represented as:

The x-axis is reference for the in phase signal whereas, y-axis displays the

quadrature component. As the quadrature component is absent in BASK system,

so the constellation diagram shows only the in-phase component along x-axis.

G. Power Efficiency

It is the ability of modulation scheme to preserve signal with low power levels and is expressed as [1]:

H. Bandwidth Efficiency

It is the capacity of modulation technique to limit data within a defined band and is represented as:

Where,

Rb: bit rate in bps

B: bandwidth of modulated RF signal

I. Power Spectral Density (PSD)

PSD demonstrates signal’s frequency response by plotting the frequency vs power. It shows the spectral power of all

the frequency contents within a signal.

J. Pulse Shaping

It is performed using specialized pulse shaping filters in the transmitter to decrease the interference between the

signals by increasing the channel bandwidth. It helps to filter out the spectrum’s side lobes as shown in Figure 4.

K. Comparison

Figure 4: Signal Spectrum before and after pulse shaping

P a g e | 21

An efficient modulation technique should exhibit following characteristics:

Low BER at less SNR

Power and bandwidth efficiency

Good performance in the presence of multipath fading

Utilize less bandwidth

Less complex and cost effective

L. Applications of ASK System

The applications of an ASK communication system are mentioned below:

Transmission of digital information in an optical fiber

Short range military communication

Early telephone modem up to 1200bps on voice grade lines

Used in RF systems for the transmission of Morse code

III. BASK SYSTEM

A. Systematic Block Diagram

P a g e | 22

The detailed block diagram is ASK communication system is shown in Figure 5.

B. Signal Modelling

System modelling is performed in Matlab and Simulink. The Matlab code is attached in Appendix A. ASK system is

composed of a transmitter, transmission medium and a receiver described below.

i. Transmitter

Band Pass

Filter

Figure 5: Systematic Block Diagram of ASK Communication System

P a g e | 23

BASK modulation is performed in the transmitter through the steps mentioned below. The ASK modulated waveform is

shown in Figure 3.

a) Signal Generation

Modulating baseband signal is expressed as a series of symbols or bits in the time domain. Each symbol represents

the information of n bits where,

N = log2m bits/symbol (11)

For the ease of representation, 16 symbols are considered in the design with 4000 bits in each symbol to achieve a

data rate of 64Kbps.

b) Carrier Generation

A continuous high frequency sinusoidal carrier is generated. The frequency of carrier should be greater than that of

baseband signal otherwise, the signal detection results in large BER at the receiver.

c) ASK Modulation

ASK modulation can be performed using a switch which only passes the carrier when the input bit is 1. When the input

bit is 0, no carrier is passed. The spectrum of ASK transmitted signal is shown in Figure 6.

ii. Channel

AWGN is added in the transmission medium. The system’s performance is analyzed in three scenarios.

a) No AWGN

When no noise is added to the system the received waveform is exactly like the transmitted waveform.

b) A constant AWGN with Eb/ No or SNR of 10dB

c) A variable AWGN with Eb/ No or SNR of 1-15dB

Figure 6: Spectrum of transmitted ASK waveform before and after AWGN

P a g e | 24

The received waveform after adding the AWGN with SNR of 1-15dB is shown in Figure 7.

iii. Receiver

In the BASK receiver, signal detection is performed to retrieve the transmitter bit information.

a) Band Pass Filtration

Band pass filter is used as the first stage of receiver to reduce the noise effects.

b) Rectification

The input signal to rectifier is multiplied with itself which rectifies the output. Therefore, only the positive side of

waveform is received at the output of rectifier.

c) Filtration

A low pass filter reduces the effect of noise from rectified signal. A least square FIR filter is designed for the removal of

noise. LPF suppresses the higher noise frequency. Rectification and filtration combines to detect the envelop of received

signal.

d) Comparator

The comparator delivers a digital output of the envelop detected signal on the basis of a threshold value. If the value of

signal is below threshold, the output is 0 whereas, the output is 1 is the value of signal is above threshold. The received

bit steam for AWGN with SNR 1-15dB is shown in Figure 8.

Figure 7: Received Signal after adding AWGN from Eb/ No = SNR 1=15dB and

filtration

P a g e | 25

e) BER

The transmitted bit stream is compared with detected bit stream to find the BER. Simulation results are then plotted

against the theoretical bit error rate for a non-coherent BASK system as shown in Figure 9. Analysis has been done for

BER 10-2 and 10-3

.

1.1.Simulink Model

Figure 8: BASK received Bit Stream with AWGN having Eb/ No = SNR 1-15dB

Figure 9: BER analysis for 10 -2 and 10-3 between theoretical and calculated results

P a g e | 26

The system modelling of ASK system is done in Simulink. Threshold for signal detection is set at 0.5. The Simulink

model is presented in Figure 10a whereas, the simulation results are presented in Figure 10b.

C. Noise Modelling

AWGN is represented by a random process with a PDF having a Gaussian distribution and a constant PSD with a

value equivalent to noise power or variance. Noise has a constant mean and covariance is time invariant making it a wide

sense stationary process. The histogram of white noise is plotted to determine its PDF. The PDF is nearly equal to the

theoretical PDF represented by the following equation with a Gaussian distribution [4].

(12)

Figure 10a: Simulink Model of ASK communication system

Figure 10b: Simulation results of ASK system in Simulink

P a g e | 27

Autocorrelation function is a scaled signal with magnitude equal to the variance. MATLAB code for the noise modelling

is attached in Appendix B. Simulation results of noise modelling are shown in Figure 11.

PSD of a white noise shows that it has nearly fixed power in the entire band with a value equal to 6dB. Thereby, it is

confirmed that the generated white noise has a constant PSD.

Power = 10log10 (σ2

) =10log10 (4) =6 dB

IV. DESIGN ANALYSIS

A. BER Comparison

The comparison of BER calculated using theoretical formula in equation 10 and the simulated results is shown in Table

1. It is found that the BER of designed BASK system is nearly equal to the theoretical results. The results can also be

verified from Figure 9.dB

TABLE I

COMPARISON OF THEORETICAL AND CALCULATED BER FOR SNR 1-15 DB

Eb/ No or SNR

(dB)

BER Theoretical BER Calculated

1 0.331902666542877 0.527366314920639

2 0.278382207307438 0.4330396525850132

3 0.223823897295794 0.353271833286657

4 0.170651194356157 0.258898845230837

Figure 11: Noise Modelling of AGWN in MATLAB showing generated noise, PDF, ACF and PSD of noise

P a g e | 28

5 0.121709824615639 0.180549318689371

6 0.079814667661548 0.111318237100481

7 0.047093102397304 0.06586618958376

8 0.024325941089215 0.034328134289297

9 0.010627897188806 0.015034552398623

10 0.003760324064043 0.005151674628544

11 0.001020091579789 0.001287084315818

12 0.000198042813939 0.000250194125872

13 0.000025228735034 0.000032213359232

14 0.000001890569040 0.000002305326446

15 0.000000072627681 0.000000085308201

It is determined that for SNR from 1-6dB there is more difference between the simulated and theoretical results.

However, if SNR is increased further, the calculated results are almost equal to the theoretical results.

When the value of SNR is less, the signal to noise ratio is less which means that the difference between desired signal

and noise energy is quiet less therefore, it becomes difficult to distinguish the data bits from noise. As a result of this, the

BER is more when SNR is less.

B. BER for Different Modulation Schemes

An ASK system with non-coherent detection has high probability of error as compared to other digital modulation

schemes. Although it is a bandwidth efficient system, but its power efficiency is low resulting in poor noise immunity

thereby, high BER.

Table 2 shows the comparison of E0/ No (dB) values of different digital modulation schemes needed to achieve a BER

of 10-6

[6].

TABLE II

EB/ NO FOR DIGITAL MODULATION TECHNIQUES TO ACHIEVE BER OF 10-6

Modulation Scheme Eb/ No (dB)

BPSK 10.6

QPSK 10.6

4-QAM 10.6

D-BPSK 11.2

D-QPSK 12.7

8-PSK 14

BASK 14

16-QAM 14.5

16-PSK 18.3

64-QAM 18.8

P a g e | 29

32-PSK 23.3

C. BASK System

ASK transmitters are simple and efficient since power is not consumed for bit 0. Receiver complexity can be reduced

by using non-coherent detection.

As BER is high with an abrupt change in the amplitude of carrier at bit transition, therefore BASK is not spectrally

efficient and is limited to low or moderate data rates as compared to other digital modulation techniques. The threshold

detection depends upon the received signal’s amplitude, so BASK has poor performance in presence of fading. This limits

the BASK communication range.

D. BASK Spectral Efficiency

The PSD of binary ASK signal is of the form of which has distribution on both sides of the vertical axis.

Therefore, the bandwidth of a binary ASK system is double than the baseband bit stream’s bandwidth. Therefore,

B= =

The bandwidth of BASK system can be verified from the generalized spectrum shown in Figure 12. This is also called

the null to null bandwidth of an ASK modulated signal. As the quadrature component is wasted in an ASK modulation

scheme, therefore the spectral efficiency is half than that of the baseband unipolar signal. The spectrum is in the form of

sinc2

, which is similar to the one obtained for the designed system shown in Figure 6.

Spectrum of ASK modulated signal is centered on the carrier frequency whereas the spectrum of bit stream is spread

along the frequency band.

E. System Limitation

The noncoherent BASK system receiver often uses a band pass filter at the first stage of receiver with a bandwidth of

2/Tb Hz centered on the carrier frequency fC Hz. However, as the data rate is very high (64Kbps), the bit duration is quiet

low. Therefore, the design of such a band pass filter is a very tedious task for the required results. An increase in the data

rate reduces the symbol’s pulse width thereby, increasing signal bandwidth.

A half wave rectifier together with a LPF forms an envelope detector. The bandwidth of low pass filter is 2/Tb Hz. This

configuration is used to detect bit stream. In the Matlab code, an envelope command is used for half wave rectification

whereas, in the Simulink model, signal is multiplied with itself for rectification. Design of low pass filter is again a limitation.

A higher cutoff frequency is used to design a more practical filter with good results.

Figure 12: Bandwidth of an ASK signal

P a g e | 30

An analog comparator with a specific threshold voltage outputs the estimate of the received binary data. At low SNR,

the received signal has more BER because of the reason that it has high false detections. If the threshold is increased to

reduce the BER for low SNR, the BER of signal with high SNR is affected. Therefore, threshold is selected to maximize

the performance of the system for wide range of SNR values.

This noncoherent BASK demodulator is not optimal because the envelope detector and comparator are not equivalent to

correlation performed in coherent detection.

For Gaussian case Matched Filter detection is optimal because it maximizes the SNR of received signal and making it

apt for detection. Matched filter allows the detection of bits which are below the threshold. But for the matched filter, the

signal that is being detected should be known. Therefore, the coherent detection provides better BER as compared to

non-coherent detection without the use of a matched filter.

F. System Improvement

To enhance the performance of communication system, digital error control codes are often used to detect and correct

the error bits [7]. The system uses complex signal processing techniques like source coding, encryption and equalization

thereby, reducing the bit error rate. This is however out of scope for this research document. The system can be improved

by following techniques:

Increase in SNR by reducing the communication distance

Decrease in data rate

Decrease in bandwidth which reduces the data rate

Use of pulse-shaping filter which reduces the sharp amplitude transition among different bits

Band limiting the transmitted ASK thereby, reducing the bandwidth

G. Advantages and Disadvantages

1. Advantages

Employed in control applications due to simple architecture and cost effectiveness

Less power consumption as the transmitter is practically off during bit 0

Simple transmitter and receiver design

2. Disadvantages

Sharp discontinuities at the transition points between binary 1 and 0

Can be easily corrupted by noise

High BER

Low SNR

Inefficient to use for multiplexing

V. CONCLUSION

A binary ASK communication system with non-coherent detection is designed using MATLAB and Simulink. The

simulation results are presented in the report. It is observed that as the signal in an ASK signal is only transmitted for half

the time if there is a 50% probability for bit 1, therefore, there is a 3dB degradation in BER as compared to that in BPSK

system where the transmission is for complete communication duration.

P a g e | 31

The designed system is analyzed for various values of Eb/No and it is examined that the performance of system at high

Eb/No is nearly similar to the theoretical results. The data rate of assigned task is quiet high for an ASK non-coherent

system therefore, at low bit energy to noise ratio, there are more deviations in the system performance as compared to

the analytical results. This can be improved by using coherent detection and reducing the data rate.

As there are sharp discontinuities in the received ASK waveform, therefore it is implied that the bandwidth is high. This

might increase the BER. However, if a band limiting or pulse shaping of the message signal is done before modulation,

the sharp discontinuities can be avoided.

Noise Analysis performed shows that the PDF and ACF of the generated white noise are in accordance to the

theoretical results with a Gaussian PDF and an even ACF centered about 0. The PSD of noise is constant over the entire

band with a level of 6dB.

ASK systems are preferred in low cost systems with a short communication distance such as RFID. Pulse shaping by

the use of a band limited filter can improve the bit error rate. The side bands in spectrum can be eliminated by using a

pulse shaping filter.

APPENDIX A

Signal modelling m.file

clc; clear all; close all;

%% ----- BASEBAND SIGNAL PARAMETERS -----%%

D_R=64e3; %Data Rate = 64Kbps

P_D=1/D_R; %Pulse duration

%%% TRANSMITTER %%%%

% SIGNAL GENERATION

bits=16;

Input=rand(1,bits)>0.5;

Input=repmat(Input',1,4000)';

Input=Input(:)';

t=linspace(0,bits,numel(Input));

figure('Name','Transmitted Data')

subplot(3,1,1);

plot(t,Input,'r');

title('INPUT BIT STREAM');

xlabel('Samples');

ylabel('Amplitude');

grid on

% CARRIER GENERATION

DC=1/2;

Ao=3;

F=10;

Carrier=Ao.*sin(2*pi*F*t)+DC;

subplot(3,1,2);

plot(t,Carrier,'b');

title('CARRIER');

xlabel('Samples');

ylabel('Amplitude');

grid;

% ASK MODULATION

ModSig=Carrier.*Input;

subplot (3,1,3);

plot(t,ModSig);

title('BASK MODULATED SIGNAL');

xlabel('Samples');

ylabel('Amplitude');

grid;

P a g e | 32

% POWER SPECTRAL DENSITY:

[Pxx,F] = periodogram(ModSig,[],length(ModSig),D_R);

figure;

plot(F,10*log10(Pxx));

xlim ([0 500]);

%%%% TRANSMISSION MEDIUM %%%%

% ZERO NOISE

No=0;

RxSig_1=ModSig+No;

% FIXED AWGN

SNRdB_C=10;

RxSig_2=awgn(ModSig,SNRdB_C,'measured',10);

% MULTIPLE AWGN

for SNRdB_=1:1:15

RxSig_3=awgn(ModSig,SNRdB_,'measured',10);

end

L1=length(RxSig_1); L2=length(RxSig_2); L3=length(RxSig_3);

%%%% RECEIVER %%%%%

% LOW PASS FILTER TO REDUCE THE EFFECT OF NOISE

LPF = fdesign.lowpass('Fp,Fst,Ap,Ast',5,20,1,30,100);

lowpass = design(LPF,'equiripple');

%BAND PASS FILTER

[ A B C D] = butter(10,[1 5]/50);

d=designfilt('bandpassfir'

,'FilterOrder',20, ...

'CutoffFrequency1',1,'CutoffFrequency2',5, ...

'SampleRate',100);

% RECEIVED BIT STREAM WITHOUT NOISE

% RECEIVED SIGNAL

figure ('Name'

,'Received Bit Stream Without AWGN');

subplot (2,1,1);

plot(t,RxSig_1);

title('BASK RECEIVED SIGNAL WITH ZERO NOISE');

xlabel('Samples');

ylabel('Amplitude');

% COMPARATOR

for a=1:1:L1

if RxSig_1(a)==0

R1(a)=0;

else

R1(a)=1;

end

end

subplot(2,1,2)

plot(t,R1);

title('RECEIVED BIT STREAM WITHOUT NOISE');

xlabel('Samples'); ylabel('Amplitude');

% RECEIVED BIT STREAM WITH CONSTANT NOISE

% RECEIVED SIGNAL

figure('Name'

,'Received Bit Stream for Fixed Noise');

subplot (4,1,1);

plot(t,RxSig_2);

legend('Signal with fixed AWGN:SNR=10dB');

title('BASK MODULATED SIGNAL WITH FIXED AWGN OF 10dB');

xlabel('Samples'); ylabel('Amplitude');

% BAND PASS FILTER

R2_F1=filter(d,R2_R);

% RECTIFICATION

R2_R=envelope(R2_F1)

;

subplot(4,1,2)

plot(t,R2_R);

P a g e | 33

% FILTERATION

R2_F=filter(lowpass,R2_R);

subplot(4,1,3)

plot(t,R2_F);

% COMPARATOR

for b=1:L2

if R2_F(b)>2

R2(b)=1;

else

R2(b)=0;

end

end

subplot(5,1,5)

plot(t,R2);

%RECEIVED BIT STREAM WITH MULTIPLE AWGN: SNR IN dB=1

-15dB

figure('Name'

,'Received Signal After Multiple AWGN');

title('BASK RECEIVED SIGNAL WITH MULTIPLE AWGN');

for SNR_dB=1:1:15

% ADDING NOISE

RxSig3=awgn(ModSig,SNR_dB,'measured',10);

% FILTERATION

R3F1= filter(d,RxSig3);

R3F=filter(lowpass,R3F1);

subplot(4,4,SNR_dB)

plot(t,RxSig3,'g'

,'LineWidth',2);

hold on

;

plot(t,R3F,'b');

title(['SNR: ',num2str(SNR_dB),'dB']);

xlim([0 16]); ylim( [

-8 8]);

xlabel('Samples'); ylabel('Amplitude');

end

legend('Signal with AWGN'

,'Signal After Filteration');

h=1; i=1; j=1; k=1; l=1; m=1;

figure('Name'

,'RECEIVED BITS AFTER AWGN: SNR=1

-15dB');

title('BASK RECEIVED BIT STREAM WITH VARIABLE NOISE');

for SNR=1:1:15

snrlin=10.^(SNR./10);

RxSig_3=awgn(ModSig,SNR,'measured',10);

R3_F=filter(lowpass,RxSig_3);

% RECTIFICATION

R3_R=envelope(R3_F);

% COMPARATOR

for Sample=1:L3

if R3_R(Sample)>2

Rx_Bits(Sample)=1;

else

Rx_Bits(Sample)=0;

end

end

subplot(5,3,SNR)

plot(t,Rx_Bits);

title(['SNR: ',num2str(SNR),'dB']);

xlabel('Samples'); ylabel('Amplitude');

xlim( [0 16]);

%%%%% BER %%%%%

error=length(find(Rx_Bits~=Input));

cber(h)=error/64000;

h=h+1;

tber(i) = 0.5*exp(

-0.5*snrlin)+0.5*qfunc(sqrt(snrlin));

snrdb(j)=SNR;

P a g e | 34

j=j+1;

end

legend('BASK Received BITSTREAM with different AWGN');

%Plotting the theoretical and calculated BER

figure ('Name','Comparison B/W Theoretical & Calculated BER');

semilogy(snrdb,cber,'-bo',snrdb,tber,'-mh')

title('BER vs Eb/No or SNR in dB');

xlabel('Signal to noise ratio'); ylabel('Bit error rate');

APPENDIX B

Noise modelling m.file

clear all; clc; close all;

Length = 64000; % Gaussian Noise Signal Length

% WHITE NOISE

n_mean = 0; % Mean

SD = 2; % Standard Deviation

W_Noise = SD * randn (Length,1) + n_mean; %White Noise

figure;

subplot(4,1,1)

plot(W_Noise);

title(['White noise : \mu_x=',num2str(n_mean),' \sigma^2=',num2str(SD^2)])

xlabel('No. of Samples'); ylabel('Sample Value'); xlim ([0 64000]); grid on;

% NOISE PDF

subplot(4,1,2)

n = 200; %Total Histrogram Bins in the noise PDF

[f,x] = hist (W_Noise,n);

Bar (x,f/trapz(x,f)); hold on;

%Theoretical PDF of Gaussian Random Variable

T_PDF_WN = (1/(sqrt(2*pi)*SD)) * exp (-((x-n_mean).^2) / (2*SD^2));

plot (x,T_PDF_WN);hold off; grid on;

title ('Theoretical PDF and Simulated PSD of White Gaussian Noise');

legend ('Histograms','Theoretical PDF'); xlabel ('Histogram'); ylabel ('PDF f_x(x)');

% NOISE ACF

subplot (4,1,3)

ACF_W_N = 1/Length * conv (flipud(W_Noise), W_Noise);

lag = (-Length+1):1:(Length-1);

plot(lag , ACF_W_N);

title('ACF of White Noise'); xlabel('Lag'); ylabel('Auto-Correlation');

xlim ([-200 200]); grid on;

% VERIFICATION OF CONSTANT PSD

n_mean = 0;

SD = 2;

S_L = 1024;

% Random White Gaussian Noise

Avg_Mean = n_mean * ones(1,S_L);

Co_Var = (SD^2) * diag(ones(S_L,1));

Chol_Cov_M = chol(Co_Var);

% Multivariate Gaussian Distribution

z = repmat(Avg_Mean,Length,1) + randn(Length,S_L)* Chol_Cov_M;

S = 1/sqrt(S_L)*fft(z,[],2);

P_Avg = mean(S.*conj(S));

Norm_Freq = [-S_L/2:S_L/2-1]/S_L;

P_Avg = fftshift(P_Avg);

subplot (4,1,4)

P a g e | 35

plot (Norm_Freq,10*log10(P_Avg),'m');

axis ([-0.5 0.5 0 10]); grid on;

ylabel('PSD in dB/Hz'); title('PSD of AWGN');

xlabel ('Normalized Frequency');

ACKNOWLEDGMENT

I wish to express my sincere gratitude to Prof. Mike Cherniakov for providing me with an opportunity to work on this

research project and sincerely thank him and Emidio Marchetti for their guidance and encouragement in carrying out this

research project.

REFERENCES

[1] “Wireless Communications- Principles and Practice”, T. Rappaport, Prentice Hall, 1996

[2] Athanasios Papoulis, Probability, Random Variables, and Stochastic Processes, 3rd ed. WCB/McGraw-Hill, 1991

[3] “Coherent and Non-coherent Receivers”, Professor Sheng Chen, School of Electronics and Computer Science, University of Southampton.

[4] “Mobile Communication Systems” Professor Z Ghassemlooy Electronics & IT Division Scholl of Engineering, Sheffield Hallam University U.K.

[5] Y. Kim, S.-W. Tam, G.-S. Byun, H. Wu, L. Nan, G. Reinman, J. Cong, and M.-C. F. Chang, “Analysis of noncoherent ASK modulation-based RFinterconnecthttp://www.6daixie.com/contents/13/2391.html

for memory interface,” IEEE J. Emerg. Sel. Topics Circuits Syst., vol. 2, no. 2, pp. 200–209, Jun. 2012

[6] “Digital Communications” by John G.Proakis, Chapter 7: Channel Capacity and Coding

[7] “Error Control Techniques and Their Applications”, Chaudhary, Rubal & Gupta, Vrinda, International Journal of Computer Applications in

Engineering Sciences, Vol I, Issue II, June 2011

 

因为专业，所以值得信赖。如有需要，请加QQ：99515681 或邮箱： 

微信：codinghelp